16x24x48 RECTANGLE Riverstone Beaded Aboveground Swimming Pool Liner 20 GA. Fanta Sea and Olympic Pools.
This 16' x 24' x 48 Rectangle Premium Virgin Vinyl Aboveground Pool Liner in Riverstone Pattern, provides maximum protection against the sun's damaging UV rays so it will last longer and maintain a beautiful appearance for years. The rugged double welded seams will withstand winter's worst. 20 Gauge Virgin Vinyl material. Provides maximum protection from the sun's damaging UV rays. Features strong double welded seams.Fits flat bottom pools with 48 inch sidewalls, including Kayak, Fanta Sea and Olympic Pools. RECOMMENDED ITEMS NEEDED FOR INSTALLATION. 2 gray duct tape with non-asphalted adhesive, garden hose, industrial vacuum or household vacuum (filter bag removed), masking tape, screwdriver, sharp nail or ice pick, tamping tool, utility knife.
WARNING: Liner should be stored at room temperature for at least 72 hours prior to installation. Spread a 2 layer of brick sand over the entire pool foundation area inside the base rails. Use a rake to make the brick sand flat and smooth. Tamp sand to help reduce footprints. In place of brick sand, you can use "Soft Step" Floor Padding.Cut the sheets to fit and join them with duct tape along the whole length of each seam. With the brick sand, make a curved cove about 4" high and 4" wide all around the bottom of the pool wall on the inside. Pool Cove can also be used. Place the closed liner carton in the center of the pool. Do NOT use anything sharp to open the carton. Unfold the liner and spread it out in the sun to warm up. Inspect all seams and surfaces for holes. The curved seam should be centered on the cove at the base of the wall. The other seams will form straight lines across the bottom of the pool. If seams appear to have flaps, check to see if correct side is up. Smooth out all wrinkles in the bottom. If you have a beaded liner, fasten the liner in place by lifting the sides of the liner and inserting the beaded edge into the liner retainer on the top edge. If you do not have a beaded liner, lift the sides of the liner and drape them over the top of the pool wall.
Fasten liner to the top of the wall with plastic coping. Let the liner hang slack for now. Do NOT pull liner tight.
Start filling the pool with water. As the pool fills, work out the wrinkles and smooth the liner to the wall. Remove the plastic coping around the top edge of the wall one piece at a time and adjust the liner.
Keep smoothing out the wrinkles. Do not install faceplates, inlets, light fixtures, etc. Until water reaches 3 below each opening. Premature installation might result in the liner tearing away from the opening due to stretching as the water level increases.
Proceed filling pool until water reaches desired level. OPTIONAL STEP TO ELIMINATE WRINKLES.
To remove air from behind the liner, which prevents wrinkles, insert a vacuum cleaner hose through the skimmer hole in the pool wall behind the liner. To minimize vacuum loss, seal the opening around the hose and the water inlet using cardboard and masking tape. While vacuum is running, you should be adjusting the liner with short tugs to eliminate wrinkles. If you have trouble shifting the liner into position, shut vacuum off for a few minutes.You should then be able to adjust the troubled area before continuing with the vacuum. The vacuum cleaner should continue to run until water level nears the top. Make sure to keep vacuum cleaner hose above the water level at all times. Oversized deliveries are curbside only with FREE Lift Gate Service. We are unable to make changes or cancellations to orders after they are placed.
If the combined weight of your order is 500 lbs. The item "16x24x48 RECTANGLE Riverstone Beaded Aboveground Swimming Pool Liner 20 GA" is in sale since Monday, October 9, 2017.This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Liners". The seller is "saveonpoolsupplies" and is located in United States. This item can be shipped to United States.